| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_ncm: Refactor bind path to use __free()
After an bind/unbind cycle, the ncm->notify_req is left stale. If a
subsequent bind fails, the unified error label attempts to free this
stale request, leading to a NULL pointer dereference when accessing
ep->ops->free_request.
Refactor the error handling in the bind path to use the __free()
automatic cleanup mechanism.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Call trace:
usb_ep_free_request+0x2c/0xec
ncm_bind+0x39c/0x3dc
usb_add_function+0xcc/0x1f0
configfs_composite_bind+0x468/0x588
gadget_bind_driver+0x104/0x270
really_probe+0x190/0x374
__driver_probe_device+0xa0/0x12c
driver_probe_device+0x3c/0x218
__device_attach_driver+0x14c/0x188
bus_for_each_drv+0x10c/0x168
__device_attach+0xfc/0x198
device_initial_probe+0x14/0x24
bus_probe_device+0x94/0x11c
device_add+0x268/0x48c
usb_add_gadget+0x198/0x28c
dwc3_gadget_init+0x700/0x858
__dwc3_set_mode+0x3cc/0x664
process_scheduled_works+0x1d8/0x488
worker_thread+0x244/0x334
kthread+0x114/0x1bc
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: asix: hold PM usage ref to avoid PM/MDIO + RTNL deadlock
Prevent USB runtime PM (autosuspend) for AX88772* in bind.
usbnet enables runtime PM (autosuspend) by default, so disabling it via
the usb_driver flag is ineffective. On AX88772B, autosuspend shows no
measurable power saving with current driver (no link partner, admin
up/down). The ~0.453 W -> ~0.248 W drop on v6.1 comes from phylib powering
the PHY off on admin-down, not from USB autosuspend.
The real hazard is that with runtime PM enabled, ndo_open() (under RTNL)
may synchronously trigger autoresume (usb_autopm_get_interface()) into
asix_resume() while the USB PM lock is held. Resume paths then invoke
phylink/phylib and MDIO, which also expect RTNL, leading to possible
deadlocks or PM lock vs MDIO wake issues.
To avoid this, keep the device runtime-PM active by taking a usage
reference in ax88772_bind() and dropping it in unbind(). A non-zero PM
usage count blocks runtime suspend regardless of userspace policy
(.../power/control - pm_runtime_allow/forbid), making this approach
robust against sysfs overrides.
Holding a runtime-PM usage ref does not affect system-wide suspend;
system sleep/resume callbacks continue to run as before. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix potential UAF in smb2_close_cached_fid()
find_or_create_cached_dir() could grab a new reference after kref_put()
had seen the refcount drop to zero but before cfid_list_lock is acquired
in smb2_close_cached_fid(), leading to use-after-free.
Switch to kref_put_lock() so cfid_release() is called with
cfid_list_lock held, closing that gap. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: Fix proto fallback detection with BPF
The sockmap feature allows bpf syscall from userspace, or based
on bpf sockops, replacing the sk_prot of sockets during protocol stack
processing with sockmap's custom read/write interfaces.
'''
tcp_rcv_state_process()
syn_recv_sock()/subflow_syn_recv_sock()
tcp_init_transfer(BPF_SOCK_OPS_PASSIVE_ESTABLISHED_CB)
bpf_skops_established <== sockops
bpf_sock_map_update(sk) <== call bpf helper
tcp_bpf_update_proto() <== update sk_prot
'''
When the server has MPTCP enabled but the client sends a TCP SYN
without MPTCP, subflow_syn_recv_sock() performs a fallback on the
subflow, replacing the subflow sk's sk_prot with the native sk_prot.
'''
subflow_syn_recv_sock()
subflow_ulp_fallback()
subflow_drop_ctx()
mptcp_subflow_ops_undo_override()
'''
Then, this subflow can be normally used by sockmap, which replaces the
native sk_prot with sockmap's custom sk_prot. The issue occurs when the
user executes accept::mptcp_stream_accept::mptcp_fallback_tcp_ops().
Here, it uses sk->sk_prot to compare with the native sk_prot, but this
is incorrect when sockmap is used, as we may incorrectly set
sk->sk_socket->ops.
This fix uses the more generic sk_family for the comparison instead.
Additionally, this also prevents a WARNING from occurring:
result from ./scripts/decode_stacktrace.sh:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 337 at net/mptcp/protocol.c:68 mptcp_stream_accept \
(net/mptcp/protocol.c:4005)
Modules linked in:
...
PKRU: 55555554
Call Trace:
<TASK>
do_accept (net/socket.c:1989)
__sys_accept4 (net/socket.c:2028 net/socket.c:2057)
__x64_sys_accept (net/socket.c:2067)
x64_sys_call (arch/x86/entry/syscall_64.c:41)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
RIP: 0033:0x7f87ac92b83d
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: avoid potential out-of-bounds in btrfs_encode_fh()
The function btrfs_encode_fh() does not properly account for the three
cases it handles.
Before writing to the file handle (fh), the function only returns to the
user BTRFS_FID_SIZE_NON_CONNECTABLE (5 dwords, 20 bytes) or
BTRFS_FID_SIZE_CONNECTABLE (8 dwords, 32 bytes).
However, when a parent exists and the root ID of the parent and the
inode are different, the function writes BTRFS_FID_SIZE_CONNECTABLE_ROOT
(10 dwords, 40 bytes).
If *max_len is not large enough, this write goes out of bounds because
BTRFS_FID_SIZE_CONNECTABLE_ROOT is greater than
BTRFS_FID_SIZE_CONNECTABLE originally returned.
This results in an 8-byte out-of-bounds write at
fid->parent_root_objectid = parent_root_id.
A previous attempt to fix this issue was made but was lost.
https://lore.kernel.org/all/4CADAEEC020000780001B32C@vpn.id2.novell.com/
Although this issue does not seem to be easily triggerable, it is a
potential memory corruption bug that should be fixed. This patch
resolves the issue by ensuring the function returns the appropriate size
for all three cases and validates that *max_len is large enough before
writing any data. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: detect invalid INLINE_DATA + EXTENTS flag combination
syzbot reported a BUG_ON in ext4_es_cache_extent() when opening a verity
file on a corrupted ext4 filesystem mounted without a journal.
The issue is that the filesystem has an inode with both the INLINE_DATA
and EXTENTS flags set:
EXT4-fs error (device loop0): ext4_cache_extents:545: inode #15:
comm syz.0.17: corrupted extent tree: lblk 0 < prev 66
Investigation revealed that the inode has both flags set:
DEBUG: inode 15 - flag=1, i_inline_off=164, has_inline=1, extents_flag=1
This is an invalid combination since an inode should have either:
- INLINE_DATA: data stored directly in the inode
- EXTENTS: data stored in extent-mapped blocks
Having both flags causes ext4_has_inline_data() to return true, skipping
extent tree validation in __ext4_iget(). The unvalidated out-of-order
extents then trigger a BUG_ON in ext4_es_cache_extent() due to integer
underflow when calculating hole sizes.
Fix this by detecting this invalid flag combination early in ext4_iget()
and rejecting the corrupted inode. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Check GuC running state before deregistering exec queue
In normal operation, a registered exec queue is disabled and
deregistered through the GuC, and freed only after the GuC confirms
completion. However, if the driver is forced to unbind while the exec
queue is still running, the user may call exec_destroy() after the GuC
has already been stopped and CT communication disabled.
In this case, the driver cannot receive a response from the GuC,
preventing proper cleanup of exec queue resources. Fix this by directly
releasing the resources when GuC is not running.
Here is the failure dmesg log:
"
[ 468.089581] ---[ end trace 0000000000000000 ]---
[ 468.089608] pci 0000:03:00.0: [drm] *ERROR* GT0: GUC ID manager unclean (1/65535)
[ 468.090558] pci 0000:03:00.0: [drm] GT0: total 65535
[ 468.090562] pci 0000:03:00.0: [drm] GT0: used 1
[ 468.090564] pci 0000:03:00.0: [drm] GT0: range 1..1 (1)
[ 468.092716] ------------[ cut here ]------------
[ 468.092719] WARNING: CPU: 14 PID: 4775 at drivers/gpu/drm/xe/xe_ttm_vram_mgr.c:298 ttm_vram_mgr_fini+0xf8/0x130 [xe]
"
v2: use xe_uc_fw_is_running() instead of xe_guc_ct_enabled().
As CT may go down and come back during VF migration.
(cherry picked from commit 9b42321a02c50a12b2beb6ae9469606257fbecea) |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: Harden userspace-supplied xdp_desc validation
Turned out certain clearly invalid values passed in xdp_desc from
userspace can pass xp_{,un}aligned_validate_desc() and then lead
to UBs or just invalid frames to be queued for xmit.
desc->len close to ``U32_MAX`` with a non-zero pool->tx_metadata_len
can cause positive integer overflow and wraparound, the same way low
enough desc->addr with a non-zero pool->tx_metadata_len can cause
negative integer overflow. Both scenarios can then pass the
validation successfully.
This doesn't happen with valid XSk applications, but can be used
to perform attacks.
Always promote desc->len to ``u64`` first to exclude positive
overflows of it. Use explicit check_{add,sub}_overflow() when
validating desc->addr (which is ``u64`` already).
bloat-o-meter reports a little growth of the code size:
add/remove: 0/0 grow/shrink: 2/1 up/down: 60/-16 (44)
Function old new delta
xskq_cons_peek_desc 299 330 +31
xsk_tx_peek_release_desc_batch 973 1002 +29
xsk_generic_xmit 3148 3132 -16
but hopefully this doesn't hurt the performance much. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: debugfs: Fix legacy mode page table dump logic
In legacy mode, SSPTPTR is ignored if TT is not 00b or 01b. SSPTPTR
maybe uninitialized or zero in that case and may cause oops like:
Oops: general protection fault, probably for non-canonical address
0xf00087d3f000f000: 0000 [#1] SMP NOPTI
CPU: 2 UID: 0 PID: 786 Comm: cat Not tainted 6.16.0 #191 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014
RIP: 0010:pgtable_walk_level+0x98/0x150
RSP: 0018:ffffc90000f279c0 EFLAGS: 00010206
RAX: 0000000040000000 RBX: ffffc90000f27ab0 RCX: 000000000000001e
RDX: 0000000000000003 RSI: f00087d3f000f000 RDI: f00087d3f0010000
RBP: ffffc90000f27a00 R08: ffffc90000f27a98 R09: 0000000000000002
R10: 0000000000000000 R11: 0000000000000000 R12: f00087d3f000f000
R13: 0000000000000000 R14: 0000000040000000 R15: ffffc90000f27a98
FS: 0000764566dcb740(0000) GS:ffff8881f812c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000764566d44000 CR3: 0000000109d81003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<TASK>
pgtable_walk_level+0x88/0x150
domain_translation_struct_show.isra.0+0x2d9/0x300
dev_domain_translation_struct_show+0x20/0x40
seq_read_iter+0x12d/0x490
...
Avoid walking the page table if TT is not 00b or 01b. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
When calling mprotect() to a large hugetlb memory area in our customer's
workload (~300GB hugetlb memory), soft lockup was observed:
watchdog: BUG: soft lockup - CPU#98 stuck for 23s! [t2_new_sysv:126916]
CPU: 98 PID: 126916 Comm: t2_new_sysv Kdump: loaded Not tainted 6.17-rc7
Hardware name: GIGACOMPUTING R2A3-T40-AAV1/Jefferson CIO, BIOS 5.4.4.1 07/15/2025
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mte_clear_page_tags+0x14/0x24
lr : mte_sync_tags+0x1c0/0x240
sp : ffff80003150bb80
x29: ffff80003150bb80 x28: ffff00739e9705a8 x27: 0000ffd2d6a00000
x26: 0000ff8e4bc00000 x25: 00e80046cde00f45 x24: 0000000000022458
x23: 0000000000000000 x22: 0000000000000004 x21: 000000011b380000
x20: ffff000000000000 x19: 000000011b379f40 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc875e0aa5e2c
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
x5 : fffffc01ce7a5c00 x4 : 00000000046cde00 x3 : fffffc0000000000
x2 : 0000000000000004 x1 : 0000000000000040 x0 : ffff0046cde7c000
Call trace:
mte_clear_page_tags+0x14/0x24
set_huge_pte_at+0x25c/0x280
hugetlb_change_protection+0x220/0x430
change_protection+0x5c/0x8c
mprotect_fixup+0x10c/0x294
do_mprotect_pkey.constprop.0+0x2e0/0x3d4
__arm64_sys_mprotect+0x24/0x44
invoke_syscall+0x50/0x160
el0_svc_common+0x48/0x144
do_el0_svc+0x30/0xe0
el0_svc+0x30/0xf0
el0t_64_sync_handler+0xc4/0x148
el0t_64_sync+0x1a4/0x1a8
Soft lockup is not triggered with THP or base page because there is
cond_resched() called for each PMD size.
Although the soft lockup was triggered by MTE, it should be not MTE
specific. The other processing which takes long time in the loop may
trigger soft lockup too.
So add cond_resched() for hugetlb to avoid soft lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: fix access race during throttle policy activation
On repeated cold boots we occasionally hit a NULL pointer crash in
blk_should_throtl() when throttling is consulted before the throttle
policy is fully enabled for the queue. Checking only q->td != NULL is
insufficient during early initialization, so blkg_to_pd() for the
throttle policy can still return NULL and blkg_to_tg() becomes NULL,
which later gets dereferenced.
Unable to handle kernel NULL pointer dereference
at virtual address 0000000000000156
...
pc : submit_bio_noacct+0x14c/0x4c8
lr : submit_bio_noacct+0x48/0x4c8
sp : ffff800087f0b690
x29: ffff800087f0b690 x28: 0000000000005f90 x27: ffff00068af393c0
x26: 0000000000080000 x25: 000000000002fbc0 x24: ffff000684ddcc70
x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000000
x20: 0000000000080000 x19: ffff000684ddcd08 x18: ffffffffffffffff
x17: 0000000000000000 x16: ffff80008132a550 x15: 0000ffff98020fff
x14: 0000000000000000 x13: 1fffe000d11d7021 x12: ffff000688eb810c
x11: ffff00077ec4bb80 x10: ffff000688dcb720 x9 : ffff80008068ef60
x8 : 00000a6fb8a86e85 x7 : 000000000000111e x6 : 0000000000000002
x5 : 0000000000000246 x4 : 0000000000015cff x3 : 0000000000394500
x2 : ffff000682e35e40 x1 : 0000000000364940 x0 : 000000000000001a
Call trace:
submit_bio_noacct+0x14c/0x4c8
verity_map+0x178/0x2c8
__map_bio+0x228/0x250
dm_submit_bio+0x1c4/0x678
__submit_bio+0x170/0x230
submit_bio_noacct_nocheck+0x16c/0x388
submit_bio_noacct+0x16c/0x4c8
submit_bio+0xb4/0x210
f2fs_submit_read_bio+0x4c/0xf0
f2fs_mpage_readpages+0x3b0/0x5f0
f2fs_readahead+0x90/0xe8
Tighten blk_throtl_activated() to also require that the throttle policy
bit is set on the queue:
return q->td != NULL &&
test_bit(blkcg_policy_throtl.plid, q->blkcg_pols);
This prevents blk_should_throtl() from accessing throttle group state
until policy data has been attached to blkgs. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Disable bottom softirqs as part of spin_lock_irq() on PREEMPT_RT
snd_pcm_group_lock_irq() acquires a spinlock_t and disables interrupts
via spin_lock_irq(). This also implicitly disables the handling of
softirqs such as TIMER_SOFTIRQ.
On PREEMPT_RT softirqs are preemptible and spin_lock_irq() does not
disable them. That means a timer can be invoked during spin_lock_irq()
on the same CPU. Due to synchronisations reasons local_bh_disable() has
a per-CPU lock named softirq_ctrl.lock which synchronizes individual
softirq against each other.
syz-bot managed to trigger a lockdep report where softirq_ctrl.lock is
acquired in hrtimer_cancel() in addition to hrtimer_run_softirq(). This
is a possible deadlock.
The softirq_ctrl.lock can not be made part of spin_lock_irq() as this
would lead to too much synchronisation against individual threads on the
system. To avoid the possible deadlock, softirqs must be manually
disabled before the lock is acquired.
Disable softirqs before the lock is acquired on PREEMPT_RT. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid NULL pointer dereference in f2fs_check_quota_consistency()
syzbot reported a f2fs bug as below:
Oops: gen[ 107.736417][ T5848] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 UID: 0 PID: 5848 Comm: syz-executor263 Tainted: G W 6.17.0-rc1-syzkaller-00014-g0e39a731820a #0 PREEMPT_{RT,(full)}
RIP: 0010:strcmp+0x3c/0xc0 lib/string.c:284
Call Trace:
<TASK>
f2fs_check_quota_consistency fs/f2fs/super.c:1188 [inline]
f2fs_check_opt_consistency+0x1378/0x2c10 fs/f2fs/super.c:1436
__f2fs_remount fs/f2fs/super.c:2653 [inline]
f2fs_reconfigure+0x482/0x1770 fs/f2fs/super.c:5297
reconfigure_super+0x224/0x890 fs/super.c:1077
do_remount fs/namespace.c:3314 [inline]
path_mount+0xd18/0xfe0 fs/namespace.c:4112
do_mount fs/namespace.c:4133 [inline]
__do_sys_mount fs/namespace.c:4344 [inline]
__se_sys_mount+0x317/0x410 fs/namespace.c:4321
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The direct reason is f2fs_check_quota_consistency() may suffer null-ptr-deref
issue in strcmp().
The bug can be reproduced w/ below scripts:
mkfs.f2fs -f /dev/vdb
mount -t f2fs -o usrquota /dev/vdb /mnt/f2fs
quotacheck -uc /mnt/f2fs/
umount /mnt/f2fs
mount -t f2fs -o usrjquota=aquota.user,jqfmt=vfsold /dev/vdb /mnt/f2fs
mount -t f2fs -o remount,usrjquota=,jqfmt=vfsold /dev/vdb /mnt/f2fs
umount /mnt/f2fs
So, before old_qname and new_qname comparison, we need to check whether
they are all valid pointers, fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix NULL pointer dereference in __dm_suspend()
There is a race condition between dm device suspend and table load that
can lead to null pointer dereference. The issue occurs when suspend is
invoked before table load completes:
BUG: kernel NULL pointer dereference, address: 0000000000000054
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 6 PID: 6798 Comm: dmsetup Not tainted 6.6.0-g7e52f5f0ca9b #62
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
RIP: 0010:blk_mq_wait_quiesce_done+0x0/0x50
Call Trace:
<TASK>
blk_mq_quiesce_queue+0x2c/0x50
dm_stop_queue+0xd/0x20
__dm_suspend+0x130/0x330
dm_suspend+0x11a/0x180
dev_suspend+0x27e/0x560
ctl_ioctl+0x4cf/0x850
dm_ctl_ioctl+0xd/0x20
vfs_ioctl+0x1d/0x50
__se_sys_ioctl+0x9b/0xc0
__x64_sys_ioctl+0x19/0x30
x64_sys_call+0x2c4a/0x4620
do_syscall_64+0x9e/0x1b0
The issue can be triggered as below:
T1 T2
dm_suspend table_load
__dm_suspend dm_setup_md_queue
dm_mq_init_request_queue
blk_mq_init_allocated_queue
=> q->mq_ops = set->ops; (1)
dm_stop_queue / dm_wait_for_completion
=> q->tag_set NULL pointer! (2)
=> q->tag_set = set; (3)
Fix this by checking if a valid table (map) exists before performing
request-based suspend and waiting for target I/O. When map is NULL,
skip these table-dependent suspend steps.
Even when map is NULL, no I/O can reach any target because there is
no table loaded; I/O submitted in this state will fail early in the
DM layer. Skipping the table-dependent suspend logic in this case
is safe and avoids NULL pointer dereferences. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix data race in CPU latency PM QoS request handling
The cpu_latency_qos_add/remove/update_request interfaces lack internal
synchronization by design, requiring the caller to ensure thread safety.
The current implementation relies on the 'pm_qos_enabled' flag, which is
insufficient to prevent concurrent access and cannot serve as a proper
synchronization mechanism. This has led to data races and list
corruption issues.
A typical race condition call trace is:
[Thread A]
ufshcd_pm_qos_exit()
--> cpu_latency_qos_remove_request()
--> cpu_latency_qos_apply();
--> pm_qos_update_target()
--> plist_del <--(1) delete plist node
--> memset(req, 0, sizeof(*req));
--> hba->pm_qos_enabled = false;
[Thread B]
ufshcd_devfreq_target
--> ufshcd_devfreq_scale
--> ufshcd_scale_clks
--> ufshcd_pm_qos_update <--(2) pm_qos_enabled is true
--> cpu_latency_qos_update_request
--> pm_qos_update_target
--> plist_del <--(3) plist node use-after-free
Introduces a dedicated mutex to serialize PM QoS operations, preventing
data races and ensuring safe access to PM QoS resources, including sysfs
interface reads. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Enforce expected_attach_type for tailcall compatibility
Yinhao et al. recently reported:
Our fuzzer tool discovered an uninitialized pointer issue in the
bpf_prog_test_run_xdp() function within the Linux kernel's BPF subsystem.
This leads to a NULL pointer dereference when a BPF program attempts to
deference the txq member of struct xdp_buff object.
The test initializes two programs of BPF_PROG_TYPE_XDP: progA acts as the
entry point for bpf_prog_test_run_xdp() and its expected_attach_type can
neither be of be BPF_XDP_DEVMAP nor BPF_XDP_CPUMAP. progA calls into a slot
of a tailcall map it owns. progB's expected_attach_type must be BPF_XDP_DEVMAP
to pass xdp_is_valid_access() validation. The program returns struct xdp_md's
egress_ifindex, and the latter is only allowed to be accessed under mentioned
expected_attach_type. progB is then inserted into the tailcall which progA
calls.
The underlying issue goes beyond XDP though. Another example are programs
of type BPF_PROG_TYPE_CGROUP_SOCK_ADDR. sock_addr_is_valid_access() as well
as sock_addr_func_proto() have different logic depending on the programs'
expected_attach_type. Similarly, a program attached to BPF_CGROUP_INET4_GETPEERNAME
should not be allowed doing a tailcall into a program which calls bpf_bind()
out of BPF which is only enabled for BPF_CGROUP_INET4_CONNECT.
In short, specifying expected_attach_type allows to open up additional
functionality or restrictions beyond what the basic bpf_prog_type enables.
The use of tailcalls must not violate these constraints. Fix it by enforcing
expected_attach_type in __bpf_prog_map_compatible().
Note that we only enforce this for tailcall maps, but not for BPF devmaps or
cpumaps: There, the programs are invoked through dev_map_bpf_prog_run*() and
cpu_map_bpf_prog_run*() which set up a new environment / context and therefore
these situations are not prone to this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm80xx: Fix array-index-out-of-of-bounds on rmmod
Since commit f7b705c238d1 ("scsi: pm80xx: Set phy_attached to zero when
device is gone") UBSAN reports:
UBSAN: array-index-out-of-bounds in drivers/scsi/pm8001/pm8001_sas.c:786:17
index 28 is out of range for type 'pm8001_phy [16]'
on rmmod when using an expander.
For a direct attached device, attached_phy contains the local phy id.
For a device behind an expander, attached_phy contains the remote phy
id, not the local phy id.
I.e. while pm8001_ha will have pm8001_ha->chip->n_phy local phys, for a
device behind an expander, attached_phy can be much larger than
pm8001_ha->chip->n_phy (depending on the amount of phys of the
expander).
E.g. on my system pm8001_ha has 8 phys with phy ids 0-7. One of the
ports has an expander connected. The expander has 31 phys with phy ids
0-30.
The pm8001_ha->phy array only contains the phys of the HBA. It does not
contain the phys of the expander. Thus, it is wrong to use attached_phy
to index the pm8001_ha->phy array for a device behind an expander.
Thus, we can only clear phy_attached for devices that are directly
attached. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: qcom: pas: Shutdown lite ADSP DTB on X1E
The ADSP firmware on X1E has separate firmware binaries for the main
firmware and the DTB. The same applies for the "lite" firmware loaded by
the boot firmware.
When preparing to load the new ADSP firmware we shutdown the lite_pas_id
for the main firmware, but we don't shutdown the corresponding lite pas_id
for the DTB. The fact that we're leaving it "running" forever becomes
obvious if you try to reuse (or just access) the memory region used by the
"lite" firmware: The &adsp_boot_mem is accessible, but accessing the
&adsp_boot_dtb_mem results in a crash.
We don't support reusing the memory regions currently, but nevertheless we
should not keep part of the lite firmware running. Fix this by adding the
lite_dtb_pas_id and shutting it down as well.
We don't have a way to detect if the lite firmware is actually running yet,
so ignore the return status of qcom_scm_pas_shutdown() for now. This was
already the case before, the assignment to "ret" is not used anywhere. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: route: Prevent rt_bind_exception() from rebinding stale fnhe
The sit driver's packet transmission path calls: sit_tunnel_xmit() ->
update_or_create_fnhe(), which lead to fnhe_remove_oldest() being called
to delete entries exceeding FNHE_RECLAIM_DEPTH+random.
The race window is between fnhe_remove_oldest() selecting fnheX for
deletion and the subsequent kfree_rcu(). During this time, the
concurrent path's __mkroute_output() -> find_exception() can fetch the
soon-to-be-deleted fnheX, and rt_bind_exception() then binds it with a
new dst using a dst_hold(). When the original fnheX is freed via RCU,
the dst reference remains permanently leaked.
CPU 0 CPU 1
__mkroute_output()
find_exception() [fnheX]
update_or_create_fnhe()
fnhe_remove_oldest() [fnheX]
rt_bind_exception() [bind dst]
RCU callback [fnheX freed, dst leak]
This issue manifests as a device reference count leak and a warning in
dmesg when unregistering the net device:
unregister_netdevice: waiting for sitX to become free. Usage count = N
Ido Schimmel provided the simple test validation method [1].
The fix clears 'oldest->fnhe_daddr' before calling fnhe_flush_routes().
Since rt_bind_exception() checks this field, setting it to zero prevents
the stale fnhe from being reused and bound to a new dst just before it
is freed.
[1]
ip netns add ns1
ip -n ns1 link set dev lo up
ip -n ns1 address add 192.0.2.1/32 dev lo
ip -n ns1 link add name dummy1 up type dummy
ip -n ns1 route add 192.0.2.2/32 dev dummy1
ip -n ns1 link add name gretap1 up arp off type gretap \
local 192.0.2.1 remote 192.0.2.2
ip -n ns1 route add 198.51.0.0/16 dev gretap1
taskset -c 0 ip netns exec ns1 mausezahn gretap1 \
-A 198.51.100.1 -B 198.51.0.0/16 -t udp -p 1000 -c 0 -q &
taskset -c 2 ip netns exec ns1 mausezahn gretap1 \
-A 198.51.100.1 -B 198.51.0.0/16 -t udp -p 1000 -c 0 -q &
sleep 10
ip netns pids ns1 | xargs kill
ip netns del ns1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: Fix race condition between concurrent dwc3_remove_requests() call paths
This patch addresses a race condition caused by unsynchronized
execution of multiple call paths invoking `dwc3_remove_requests()`,
leading to premature freeing of USB requests and subsequent crashes.
Three distinct execution paths interact with `dwc3_remove_requests()`:
Path 1:
Triggered via `dwc3_gadget_reset_interrupt()` during USB reset
handling. The call stack includes:
- `dwc3_ep0_reset_state()`
- `dwc3_ep0_stall_and_restart()`
- `dwc3_ep0_out_start()`
- `dwc3_remove_requests()`
- `dwc3_gadget_del_and_unmap_request()`
Path 2:
Also initiated from `dwc3_gadget_reset_interrupt()`, but through
`dwc3_stop_active_transfers()`. The call stack includes:
- `dwc3_stop_active_transfers()`
- `dwc3_remove_requests()`
- `dwc3_gadget_del_and_unmap_request()`
Path 3:
Occurs independently during `adb root` execution, which triggers
USB function unbind and bind operations. The sequence includes:
- `gserial_disconnect()`
- `usb_ep_disable()`
- `dwc3_gadget_ep_disable()`
- `dwc3_remove_requests()` with `-ESHUTDOWN` status
Path 3 operates asynchronously and lacks synchronization with Paths
1 and 2. When Path 3 completes, it disables endpoints and frees 'out'
requests. If Paths 1 or 2 are still processing these requests,
accessing freed memory leads to a crash due to use-after-free conditions.
To fix this added check for request completion and skip processing
if already completed and added the request status for ep0 while queue. |
