| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix potential deadlock in cpu hotplug with osnoise
The following sequence may leads deadlock in cpu hotplug:
task1 task2 task3
----- ----- -----
mutex_lock(&interface_lock)
[CPU GOING OFFLINE]
cpus_write_lock();
osnoise_cpu_die();
kthread_stop(task3);
wait_for_completion();
osnoise_sleep();
mutex_lock(&interface_lock);
cpus_read_lock();
[DEAD LOCK]
Fix by swap the order of cpus_read_lock() and mutex_lock(&interface_lock). |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Drain deferred trigger frees if kthread creation fails
Boot-time trigger registration can fail before the trigger-data cleanup
kthread exists. Deferring those frees until late init is fine, but the
post-boot fallback must still drain the deferred list if kthread
creation never succeeds.
Otherwise, boot-deferred nodes can accumulate on
trigger_data_free_list, later frees fall back to synchronously freeing
only the current object, and the older queued entries are leaked
forever.
To trigger this, add the following to the kernel command line:
trace_event=sched_switch trace_trigger=sched_switch.traceon,sched_switch.traceon
The second traceon trigger will fail and be freed. This triggers a NULL
pointer dereference and crashes the kernel.
Keep the deferred boot-time behavior, but when kthread creation fails,
drain the whole queued list synchronously. Do the same in the late-init
drain path so queued entries are not stranded there either. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: spi-fsl-lpspi: fix teardown order issue (UAF)
There is a teardown order issue in the driver. The SPI controller is
registered using devm_spi_register_controller(), which delays
unregistration of the SPI controller until after the fsl_lpspi_remove()
function returns.
As the fsl_lpspi_remove() function synchronously tears down the DMA
channels, a running SPI transfer triggers the following NULL pointer
dereference due to use after free:
| fsl_lpspi 42550000.spi: I/O Error in DMA RX
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[...]
| Call trace:
| fsl_lpspi_dma_transfer+0x260/0x340 [spi_fsl_lpspi]
| fsl_lpspi_transfer_one+0x198/0x448 [spi_fsl_lpspi]
| spi_transfer_one_message+0x49c/0x7c8
| __spi_pump_transfer_message+0x120/0x420
| __spi_sync+0x2c4/0x520
| spi_sync+0x34/0x60
| spidev_message+0x20c/0x378 [spidev]
| spidev_ioctl+0x398/0x750 [spidev]
[...]
Switch from devm_spi_register_controller() to spi_register_controller() in
fsl_lpspi_probe() and add the corresponding spi_unregister_controller() in
fsl_lpspi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Initialize free_qp completion before using it
In irdma_create_qp, if ib_copy_to_udata fails, it will call
irdma_destroy_qp to clean up which will attempt to wait on
the free_qp completion, which is not initialized yet. Fix this
by initializing the completion before the ib_copy_to_udata call. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/efa: Fix use of completion ctx after free
On admin queue completion handling, if the admin command completed with
error we print data from the completion context. The issue is that we
already freed the completion context in polling/interrupts handler which
means we print data from context in an unknown state (it might be
already used again).
Change the admin submission flow so alloc/dealloc of the context will be
symmetric and dealloc will be called after any potential use of the
context. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: clamp SCO altsetting table indices
btusb_work() maps the number of active SCO links to USB alternate
settings through a three-entry lookup table when CVSD traffic uses
transparent voice settings. The lookup currently indexes alts[] with
data->sco_num - 1 without first constraining sco_num to the number of
available table entries.
While the table only defines alternate settings for up to three SCO
links, data->sco_num comes from hci_conn_num() and is used directly.
Cap the lookup to the last table entry before indexing it so the
driver keeps selecting the highest supported alternate setting without
reading past alts[]. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: serialize btintel_hw_error() with hci_req_sync_lock
btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET
and Intel exception-info retrieval) without holding
hci_req_sync_lock(). This lets it race against
hci_dev_do_close() -> btintel_shutdown_combined(), which also runs
__hci_cmd_sync() under the same lock. When both paths manipulate
hdev->req_status/req_rsp concurrently, the close path may free the
response skb first, and the still-running hw_error path hits a
slab-use-after-free in kfree_skb().
Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it
is serialized with every other synchronous HCI command issuer.
Below is the data race report and the kasan report:
BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined
read of hdev->req_rsp at net/bluetooth/hci_sync.c:199
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254
hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030
write/free by task ioctl/22580:
btintel_shutdown_combined+0xd0/0x360
drivers/bluetooth/btintel.c:3648
hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246
hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526
BUG: KASAN: slab-use-after-free in
sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202
Read of size 4 at addr ffff888144a738dc
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix drm_edid leak in amdgpu_dm
[WHAT]
When a sink is connected, aconnector->drm_edid was overwritten without
freeing the previous allocation, causing a memory leak on resume.
[HOW]
Free the previous drm_edid before updating it.
(cherry picked from commit 52024a94e7111366141cfc5d888b2ef011f879e5) |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: nci: fix circular locking dependency in nci_close_device
nci_close_device() flushes rx_wq and tx_wq while holding req_lock.
This causes a circular locking dependency because nci_rx_work()
running on rx_wq can end up taking req_lock too:
nci_rx_work -> nci_rx_data_packet -> nci_data_exchange_complete
-> __sk_destruct -> rawsock_destruct -> nfc_deactivate_target
-> nci_deactivate_target -> nci_request -> mutex_lock(&ndev->req_lock)
Move the flush of rx_wq after req_lock has been released.
This should safe (I think) because NCI_UP has already been cleared
and the transport is closed, so the work will see it and return
-ENETDOWN.
NIPA has been hitting this running the nci selftest with a debug
kernel on roughly 4% of the runs. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: prevent immediate PASID reuse case
PASID resue could cause interrupt issue when process
immediately runs into hw state left by previous
process exited with the same PASID, it's possible that
page faults are still pending in the IH ring buffer when
the process exits and frees up its PASID. To prevent the
case, it uses idr cyclic allocator same as kernel pid's.
(cherry picked from commit 8f1de51f49be692de137c8525106e0fce2d1912d) |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Validate PDU length before reading SDU length in l2cap_ecred_data_rcv()
l2cap_ecred_data_rcv() reads the SDU length field from skb->data using
get_unaligned_le16() without first verifying that skb contains at least
L2CAP_SDULEN_SIZE (2) bytes. When skb->len is less than 2, this reads
past the valid data in the skb.
The ERTM reassembly path correctly calls pskb_may_pull() before reading
the SDU length (l2cap_reassemble_sdu, L2CAP_SAR_START case). Apply the
same validation to the Enhanced Credit Based Flow Control data path. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: set fileio bio failed in short read case
For file-backed mount, IO requests are handled by vfs_iocb_iter_read().
However, it can be interrupted by SIGKILL, returning the number of
bytes actually copied. Unused folios in bio are unexpectedly marked
as uptodate.
vfs_read
filemap_read
filemap_get_pages
filemap_readahead
erofs_fileio_readahead
erofs_fileio_rq_submit
vfs_iocb_iter_read
filemap_read
filemap_get_pages <= detect signal
erofs_fileio_ki_complete <= set all folios uptodate
This patch addresses this by setting short read bio with an error
directly. |
| In the Linux kernel, the following vulnerability has been resolved:
af_key: validate families in pfkey_send_migrate()
syzbot was able to trigger a crash in skb_put() [1]
Issue is that pfkey_send_migrate() does not check old/new families,
and that set_ipsecrequest() @family argument was truncated,
thus possibly overfilling the skb.
Validate families early, do not wait set_ipsecrequest().
[1]
skbuff: skb_over_panic: text:ffffffff8a752120 len:392 put:16 head:ffff88802a4ad040 data:ffff88802a4ad040 tail:0x188 end:0x180 dev:<NULL>
kernel BUG at net/core/skbuff.c:214 !
Call Trace:
<TASK>
skb_over_panic net/core/skbuff.c:219 [inline]
skb_put+0x159/0x210 net/core/skbuff.c:2655
skb_put_zero include/linux/skbuff.h:2788 [inline]
set_ipsecrequest net/key/af_key.c:3532 [inline]
pfkey_send_migrate+0x1270/0x2e50 net/key/af_key.c:3636
km_migrate+0x155/0x260 net/xfrm/xfrm_state.c:2848
xfrm_migrate+0x2140/0x2450 net/xfrm/xfrm_policy.c:4705
xfrm_do_migrate+0x8ff/0xaa0 net/xfrm/xfrm_user.c:3150 |
| In the Linux kernel, the following vulnerability has been resolved:
esp: fix skb leak with espintcp and async crypto
When the TX queue for espintcp is full, esp_output_tail_tcp will
return an error and not free the skb, because with synchronous crypto,
the common xfrm output code will drop the packet for us.
With async crypto (esp_output_done), we need to drop the skb when
esp_output_tail_tcp returns an error. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/region: Fix leakage in __construct_region()
Failing the first sysfs_update_group() needs to explicitly
kfree the resource as it is too early for cxl_region_iomem_release()
to do so. |
| In the Linux kernel, the following vulnerability has been resolved:
module: Fix kernel panic when a symbol st_shndx is out of bounds
The module loader doesn't check for bounds of the ELF section index in
simplify_symbols():
for (i = 1; i < symsec->sh_size / sizeof(Elf_Sym); i++) {
const char *name = info->strtab + sym[i].st_name;
switch (sym[i].st_shndx) {
case SHN_COMMON:
[...]
default:
/* Divert to percpu allocation if a percpu var. */
if (sym[i].st_shndx == info->index.pcpu)
secbase = (unsigned long)mod_percpu(mod);
else
/** HERE --> **/ secbase = info->sechdrs[sym[i].st_shndx].sh_addr;
sym[i].st_value += secbase;
break;
}
}
A symbol with an out-of-bounds st_shndx value, for example 0xffff
(known as SHN_XINDEX or SHN_HIRESERVE), may cause a kernel panic:
BUG: unable to handle page fault for address: ...
RIP: 0010:simplify_symbols+0x2b2/0x480
...
Kernel panic - not syncing: Fatal exception
This can happen when module ELF is legitimately using SHN_XINDEX or
when it is corrupted.
Add a bounds check in simplify_symbols() to validate that st_shndx is
within the valid range before using it.
This issue was discovered due to a bug in llvm-objcopy, see relevant
discussion for details [1].
[1] https://lore.kernel.org/linux-modules/20251224005752.201911-1-ihor.solodrai@linux.dev/ |
| In the Linux kernel, the following vulnerability has been resolved:
HID: magicmouse: avoid memory leak in magicmouse_report_fixup()
The magicmouse_report_fixup() function was returning a
newly kmemdup()-allocated buffer, but never freeing it.
The caller of report_fixup() does not take ownership of the returned
pointer, but it *is* permitted to return a sub-portion of the input
rdesc, whose lifetime is managed by the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: meson-spicc: Fix double-put in remove path
meson_spicc_probe() registers the controller with
devm_spi_register_controller(), so teardown already drops the
controller reference via devm cleanup.
Calling spi_controller_put() again in meson_spicc_remove()
causes a double-put. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: asus: avoid memory leak in asus_report_fixup()
The asus_report_fixup() function was returning a newly allocated
kmemdup()-allocated buffer, but never freeing it. Switch to
devm_kzalloc() to ensure the memory is managed and freed automatically
when the device is removed.
The caller of report_fixup() does not take ownership of the returned
pointer, but it is permitted to return a pointer whose lifetime is at
least that of the input buffer.
Also fix a harmless out-of-bounds read by copying only the original
descriptor size. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: set BTRFS_ROOT_ORPHAN_CLEANUP during subvol create
We have recently observed a number of subvolumes with broken dentries.
ls-ing the parent dir looks like:
drwxrwxrwt 1 root root 16 Jan 23 16:49 .
drwxr-xr-x 1 root root 24 Jan 23 16:48 ..
d????????? ? ? ? ? ? broken_subvol
and similarly stat-ing the file fails.
In this state, deleting the subvol fails with ENOENT, but attempting to
create a new file or subvol over it errors out with EEXIST and even
aborts the fs. Which leaves us a bit stuck.
dmesg contains a single notable error message reading:
"could not do orphan cleanup -2"
2 is ENOENT and the error comes from the failure handling path of
btrfs_orphan_cleanup(), with the stack leading back up to
btrfs_lookup().
btrfs_lookup
btrfs_lookup_dentry
btrfs_orphan_cleanup // prints that message and returns -ENOENT
After some detailed inspection of the internal state, it became clear
that:
- there are no orphan items for the subvol
- the subvol is otherwise healthy looking, it is not half-deleted or
anything, there is no drop progress, etc.
- the subvol was created a while ago and does the meaningful first
btrfs_orphan_cleanup() call that sets BTRFS_ROOT_ORPHAN_CLEANUP much
later.
- after btrfs_orphan_cleanup() fails, btrfs_lookup_dentry() returns -ENOENT,
which results in a negative dentry for the subvolume via
d_splice_alias(NULL, dentry), leading to the observed behavior. The
bug can be mitigated by dropping the dentry cache, at which point we
can successfully delete the subvolume if we want.
i.e.,
btrfs_lookup()
btrfs_lookup_dentry()
if (!sb_rdonly(inode->vfs_inode)->vfs_inode)
btrfs_orphan_cleanup(sub_root)
test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP)
btrfs_search_slot() // finds orphan item for inode N
...
prints "could not do orphan cleanup -2"
if (inode == ERR_PTR(-ENOENT))
inode = NULL;
return d_splice_alias(NULL, dentry) // NEGATIVE DENTRY for valid subvolume
btrfs_orphan_cleanup() does test_and_set_bit(BTRFS_ROOT_ORPHAN_CLEANUP)
on the root when it runs, so it cannot run more than once on a given
root, so something else must run concurrently. However, the obvious
routes to deleting an orphan when nlinks goes to 0 should not be able to
run without first doing a lookup into the subvolume, which should run
btrfs_orphan_cleanup() and set the bit.
The final important observation is that create_subvol() calls
d_instantiate_new() but does not set BTRFS_ROOT_ORPHAN_CLEANUP, so if
the dentry cache gets dropped, the next lookup into the subvolume will
make a real call into btrfs_orphan_cleanup() for the first time. This
opens up the possibility of concurrently deleting the inode/orphan items
but most typical evict() paths will be holding a reference on the parent
dentry (child dentry holds parent->d_lockref.count via dget in
d_alloc(), released in __dentry_kill()) and prevent the parent from
being removed from the dentry cache.
The one exception is delayed iputs. Ordered extent creation calls
igrab() on the inode. If the file is unlinked and closed while those
refs are held, iput() in __dentry_kill() decrements i_count but does
not trigger eviction (i_count > 0). The child dentry is freed and the
subvol dentry's d_lockref.count drops to 0, making it evictable while
the inode is still alive.
Since there are two races (the race between writeback and unlink and
the race between lookup and delayed iputs), and there are too many moving
parts, the following three diagrams show the complete picture.
(Only the second and third are races)
Phase 1:
Create Subvol in dentry cache without BTRFS_ROOT_ORPHAN_CLEANUP set
btrfs_mksubvol()
lookup_one_len()
__lookup_slow()
d_alloc_parallel()
__d_alloc() // d_lockref.count = 1
create_subvol(dentry)
// doesn't touch the bit..
d_instantiate_new(dentry, inode) // dentry in cache with d_lockref.c
---truncated--- |
