| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio with a
larger queue depth against nvmet-pci-epf:
arm-smmu-v3 fc900000.iommu: 0x0000010000000010
arm-smmu-v3 fc900000.iommu: 0x0000020000000000
arm-smmu-v3 fc900000.iommu: 0x000000090000f040
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: event: F_TRANSLATION client: 0000:01:00.0 sid: 0x100 ssid: 0x0 iova: 0x90000f040 ipa: 0x0
arm-smmu-v3 fc900000.iommu: unpriv data write s1 "Input address caused fault" stag: 0x0
Flush the write by performing a readl() of the same address to ensure that
the write has reached the destination before the ATU entry is unmapped.
The same problem was solved for dw_pcie_ep_raise_msi_irq() in commit
8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping"), but there
it was solved by dedicating an outbound iATU only for MSI. We can't do the
same for MSI-X because each vector can have a different msg_addr and the
msg_addr may be changed while the vector is masked.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix locking for bcm_op runtime updates
Commit c2aba69d0c36 ("can: bcm: add locking for bcm_op runtime updates")
added a locking for some variables that can be modified at runtime when
updating the sending bcm_op with a new TX_SETUP command in bcm_tx_setup().
Usually the RX_SETUP only handles and filters incoming traffic with one
exception: When the RX_RTR_FRAME flag is set a predefined CAN frame is
sent when a specific RTR frame is received. Therefore the rx bcm_op uses
bcm_can_tx() which uses the bcm_tx_lock that was only initialized in
bcm_tx_setup(). Add the missing spin_lock_init() when allocating the
bcm_op in bcm_rx_setup() to handle the RTR case properly. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: validate USB endpoints
The kalmia driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/client: Do not destroy NULL modes
'modes' in drm_client_modeset_probe may fail to kcalloc. If this
occurs, we jump to 'out', calling modes_destroy on it, which
dereferences it. This may result in a NULL pointer dereference in the
error case. Prevent that. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: radiotap: reject radiotap with unknown bits
The radiotap parser is currently only used with the radiotap
namespace (not with vendor namespaces), but if the undefined
field 18 is used, the alignment/size is unknown as well. In
this case, iterator->_next_ns_data isn't initialized (it's
only set for skipping vendor namespaces), and syzbot points
out that we later compare against this uninitialized value.
Fix this by moving the rejection of unknown radiotap fields
down to after the in-namespace lookup, so it will really use
iterator->_next_ns_data only for vendor namespaces, even in
case undefined fields are present. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: register phy led_triggers during probe to avoid AB-BA deadlock
There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and
LED_TRIGGER_PHY are enabled:
[ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock);
[ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234
[ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c
[ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c
[ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0
[ 1362.075849] [<806d714c>] __dev_open+0x280/0x2b0
[ 1362.080384] [<806d7668>] __dev_change_flags+0x244/0x24c
[ 1362.085598] [<806d7698>] dev_change_flags+0x28/0x78
[ 1362.090528] [<807150e4>] dev_ioctl+0x4c0/0x654 <-- Hold lock "rtnl_mutex" by calling rtnl_lock();
[ 1362.094985] [<80694360>] sock_ioctl+0x2f4/0x4e0
[ 1362.099567] [<802e9c4c>] sys_ioctl+0x32c/0xd8c
[ 1362.104022] [<80014504>] syscall_common+0x34/0x58
Here LED_TRIGGER_PHY is registering LED triggers during phy_attach
while holding RTNL and then taking triggers_list_lock.
[ 1362.191101] [<806c2640>] register_netdevice_notifier+0x60/0x168 <-- Trying to get lock "rtnl_mutex" via rtnl_lock();
[ 1362.197073] [<805504ac>] netdev_trig_activate+0x194/0x1e4
[ 1362.202490] [<8054e28c>] led_trigger_set+0x1d4/0x360 <-- Hold lock "triggers_list_lock" by down_read(&triggers_list_lock);
[ 1362.207511] [<8054eb38>] led_trigger_write+0xd8/0x14c
[ 1362.212566] [<80381d98>] sysfs_kf_bin_write+0x80/0xbc
[ 1362.217688] [<8037fcd8>] kernfs_fop_write_iter+0x17c/0x28c
[ 1362.223174] [<802cbd70>] vfs_write+0x21c/0x3c4
[ 1362.227712] [<802cc0c4>] ksys_write+0x78/0x12c
[ 1362.232164] [<80014504>] syscall_common+0x34/0x58
Here LEDS_TRIGGER_NETDEV is being enabled on an LED. It first takes
triggers_list_lock and then RTNL. A classical AB-BA deadlock.
phy_led_triggers_registers() does not require the RTNL, it does not
make any calls into the network stack which require protection. There
is also no requirement the PHY has been attached to a MAC, the
triggers only make use of phydev state. This allows the call to
phy_led_triggers_registers() to be placed elsewhere. PHY probe() and
release() don't hold RTNL, so solving the AB-BA deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-sysman: Don't hex dump plaintext password data
set_new_password() hex dumps the entire buffer, which contains plaintext
password data, including current and new passwords. Remove the hex dump
to avoid leaking credentials. |
| In the Linux kernel, the following vulnerability has been resolved:
sched/deadline: Fix missing ENQUEUE_REPLENISH during PI de-boosting
Running stress-ng --schedpolicy 0 on an RT kernel on a big machine
might lead to the following WARNINGs (edited).
sched: DL de-boosted task PID 22725: REPLENISH flag missing
WARNING: CPU: 93 PID: 0 at kernel/sched/deadline.c:239 dequeue_task_dl+0x15c/0x1f8
... (running_bw underflow)
Call trace:
dequeue_task_dl+0x15c/0x1f8 (P)
dequeue_task+0x80/0x168
deactivate_task+0x24/0x50
push_dl_task+0x264/0x2e0
dl_task_timer+0x1b0/0x228
__hrtimer_run_queues+0x188/0x378
hrtimer_interrupt+0xfc/0x260
...
The problem is that when a SCHED_DEADLINE task (lock holder) is
changed to a lower priority class via sched_setscheduler(), it may
fail to properly inherit the parameters of potential DEADLINE donors
if it didn't already inherit them in the past (shorter deadline than
donor's at that time). This might lead to bandwidth accounting
corruption, as enqueue_task_dl() won't recognize the lock holder as
boosted.
The scenario occurs when:
1. A DEADLINE task (donor) blocks on a PI mutex held by another
DEADLINE task (holder), but the holder doesn't inherit parameters
(e.g., it already has a shorter deadline)
2. sched_setscheduler() changes the holder from DEADLINE to a lower
class while still holding the mutex
3. The holder should now inherit DEADLINE parameters from the donor
and be enqueued with ENQUEUE_REPLENISH, but this doesn't happen
Fix the issue by introducing __setscheduler_dl_pi(), which detects when
a DEADLINE (proper or boosted) task gets setscheduled to a lower
priority class. In case, the function makes the task inherit DEADLINE
parameters of the donoer (pi_se) and sets ENQUEUE_REPLENISH flag to
ensure proper bandwidth accounting during the next enqueue operation. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: rawsock: cancel tx_work before socket teardown
In rawsock_release(), cancel any pending tx_work and purge the write
queue before orphaning the socket. rawsock_tx_work runs on the system
workqueue and calls nfc_data_exchange which dereferences the NCI
device. Without synchronization, tx_work can race with socket and
device teardown when a process is killed (e.g. by SIGKILL), leading
to use-after-free or leaked references.
Set SEND_SHUTDOWN first so that if tx_work is already running it will
see the flag and skip transmitting, then use cancel_work_sync to wait
for any in-progress execution to finish, and finally purge any
remaining queued skbs. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: thp: deny THP for files on anonymous inodes
file_thp_enabled() incorrectly allows THP for files on anonymous inodes
(e.g. guest_memfd and secretmem). These files are created via
alloc_file_pseudo(), which does not call get_write_access() and leaves
inode->i_writecount at 0. Combined with S_ISREG(inode->i_mode) being
true, they appear as read-only regular files when
CONFIG_READ_ONLY_THP_FOR_FS is enabled, making them eligible for THP
collapse.
Anonymous inodes can never pass the inode_is_open_for_write() check
since their i_writecount is never incremented through the normal VFS
open path. The right thing to do is to exclude them from THP eligibility
altogether, since CONFIG_READ_ONLY_THP_FOR_FS was designed for real
filesystem files (e.g. shared libraries), not for pseudo-filesystem
inodes.
For guest_memfd, this allows khugepaged and MADV_COLLAPSE to create
large folios in the page cache via the collapse path, but the
guest_memfd fault handler does not support large folios. This triggers
WARN_ON_ONCE(folio_test_large(folio)) in kvm_gmem_fault_user_mapping().
For secretmem, collapse_file() tries to copy page contents through the
direct map, but secretmem pages are removed from the direct map. This
can result in a kernel crash:
BUG: unable to handle page fault for address: ffff88810284d000
RIP: 0010:memcpy_orig+0x16/0x130
Call Trace:
collapse_file
hpage_collapse_scan_file
madvise_collapse
Secretmem is not affected by the crash on upstream as the memory failure
recovery handles the failed copy gracefully, but it still triggers
confusing false memory failure reports:
Memory failure: 0x106d96f: recovery action for clean unevictable
LRU page: Recovered
Check IS_ANON_FILE(inode) in file_thp_enabled() to deny THP for all
anonymous inode files. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: change XDP RxQ frag_size from DMA write length to xdp.frame_sz
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buff size instead
of DMA write size. Different assumptions in ice driver configuration lead
to negative tailroom.
This allows to trigger kernel panic, when using
XDP_ADJUST_TAIL_GROW_MULTI_BUFF xskxceiver test and changing packet size to
6912 and the requested offset to a huge value, e.g.
XSK_UMEM__MAX_FRAME_SIZE * 100.
Due to other quirks of the ZC configuration in ice, panic is not observed
in ZC mode, but tailroom growing still fails when it should not.
Use fill queue buffer truesize instead of DMA write size in XDP RxQ info.
Fix ZC mode too by using the new helper. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ife: Fix metalist update behavior
Whenever an ife action replace changes the metalist, instead of
replacing the old data on the metalist, the current ife code is appending
the new metadata. Aside from being innapropriate behavior, this may lead
to an unbounded addition of metadata to the metalist which might cause an
out of bounds error when running the encode op:
[ 138.423369][ C1] ==================================================================
[ 138.424317][ C1] BUG: KASAN: slab-out-of-bounds in ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.424906][ C1] Write of size 4 at addr ffff8880077f4ffe by task ife_out_out_bou/255
[ 138.425778][ C1] CPU: 1 UID: 0 PID: 255 Comm: ife_out_out_bou Not tainted 7.0.0-rc1-00169-gfbdfa8da05b6 #624 PREEMPT(full)
[ 138.425795][ C1] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 138.425800][ C1] Call Trace:
[ 138.425804][ C1] <IRQ>
[ 138.425808][ C1] dump_stack_lvl (lib/dump_stack.c:122)
[ 138.425828][ C1] print_report (mm/kasan/report.c:379 mm/kasan/report.c:482)
[ 138.425839][ C1] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 138.425844][ C1] ? __virt_addr_valid (./arch/x86/include/asm/preempt.h:95 (discriminator 1) ./include/linux/rcupdate.h:975 (discriminator 1) ./include/linux/mmzone.h:2207 (discriminator 1) arch/x86/mm/physaddr.c:54 (discriminator 1))
[ 138.425853][ C1] ? ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.425859][ C1] kasan_report (mm/kasan/report.c:221 mm/kasan/report.c:597)
[ 138.425868][ C1] ? ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.425878][ C1] kasan_check_range (mm/kasan/generic.c:186 (discriminator 1) mm/kasan/generic.c:200 (discriminator 1))
[ 138.425884][ C1] __asan_memset (mm/kasan/shadow.c:84 (discriminator 2))
[ 138.425889][ C1] ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.425893][ C1] ? ife_tlv_meta_encode (net/ife/ife.c:171)
[ 138.425898][ C1] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 138.425903][ C1] ife_encode_meta_u16 (net/sched/act_ife.c:57)
[ 138.425910][ C1] ? __pfx_do_raw_spin_lock (kernel/locking/spinlock_debug.c:114)
[ 138.425916][ C1] ? __asan_memcpy (mm/kasan/shadow.c:105 (discriminator 3))
[ 138.425921][ C1] ? __pfx_ife_encode_meta_u16 (net/sched/act_ife.c:45)
[ 138.425927][ C1] ? srso_alias_return_thunk (arch/x86/lib/retpoline.S:221)
[ 138.425931][ C1] tcf_ife_act (net/sched/act_ife.c:847 net/sched/act_ife.c:879)
To solve this issue, fix the replace behavior by adding the metalist to
the ife rcu data structure. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix WARN_ON in tracing_buffers_mmap_close
When a process forks, the child process copies the parent's VMAs but the
user_mapped reference count is not incremented. As a result, when both the
parent and child processes exit, tracing_buffers_mmap_close() is called
twice. On the second call, user_mapped is already 0, causing the function to
return -ENODEV and triggering a WARN_ON.
Normally, this isn't an issue as the memory is mapped with VM_DONTCOPY set.
But this is only a hint, and the application can call
madvise(MADVISE_DOFORK) which resets the VM_DONTCOPY flag. When the
application does that, it can trigger this issue on fork.
Fix it by incrementing the user_mapped reference count without re-mapping
the pages in the VMA's open callback. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix nd_tbl NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never
initialized because inet6_init() exits before ndisc_init() is called
which initializes it. Then, if neigh_suppress is enabled and an ICMPv6
Neighbor Discovery packet reaches the bridge, br_do_suppress_nd() will
dereference ipv6_stub->nd_tbl which is NULL, passing it to
neigh_lookup(). This causes a kernel NULL pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000268
Oops: 0000 [#1] PREEMPT SMP NOPTI
[...]
RIP: 0010:neigh_lookup+0x16/0xe0
[...]
Call Trace:
<IRQ>
? neigh_lookup+0x16/0xe0
br_do_suppress_nd+0x160/0x290 [bridge]
br_handle_frame_finish+0x500/0x620 [bridge]
br_handle_frame+0x353/0x440 [bridge]
__netif_receive_skb_core.constprop.0+0x298/0x1110
__netif_receive_skb_one_core+0x3d/0xa0
process_backlog+0xa0/0x140
__napi_poll+0x2c/0x170
net_rx_action+0x2c4/0x3a0
handle_softirqs+0xd0/0x270
do_softirq+0x3f/0x60
Fix this by replacing IS_ENABLED(IPV6) call with ipv6_mod_enabled() in
the callers. This is in essence disabling NS/NA suppression when IPv6 is
disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, arm64: Force 8-byte alignment for JIT buffer to prevent atomic tearing
struct bpf_plt contains a u64 target field. Currently, the BPF JIT
allocator requests an alignment of 4 bytes (sizeof(u32)) for the JIT
buffer.
Because the base address of the JIT buffer can be 4-byte aligned (e.g.,
ending in 0x4 or 0xc), the relative padding logic in build_plt() fails
to ensure that target lands on an 8-byte boundary.
This leads to two issues:
1. UBSAN reports misaligned-access warnings when dereferencing the
structure.
2. More critically, target is updated concurrently via WRITE_ONCE() in
bpf_arch_text_poke() while the JIT'd code executes ldr. On arm64,
64-bit loads/stores are only guaranteed to be single-copy atomic if
they are 64-bit aligned. A misaligned target risks a torn read,
causing the JIT to jump to a corrupted address.
Fix this by increasing the allocation alignment requirement to 8 bytes
(sizeof(u64)) in bpf_jit_binary_pack_alloc(). This anchors the base of
the JIT buffer to an 8-byte boundary, allowing the relative padding math
in build_plt() to correctly align the target field. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/ionic: Fix kernel stack leak in ionic_create_cq()
struct ionic_cq_resp resp {
__u32 cqid[2]; // offset 0 - PARTIALLY SET (see below)
__u8 udma_mask; // offset 8 - SET (resp.udma_mask = vcq->udma_mask)
__u8 rsvd[7]; // offset 9 - NEVER SET <- LEAK
};
rsvd[7]: 7 bytes of stack memory leaked unconditionally.
cqid[2]: The loop at line 1256 iterates over udma_idx but skips indices
where !(vcq->udma_mask & BIT(udma_idx)). The array has 2 entries but
udma_count could be 1, meaning cqid[1] might never be written via
ionic_create_cq_common(). If udma_mask only has bit 0 set, cqid[1] (4
bytes) is also leaked. So potentially 11 bytes leaked. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix incorrect buffer cleanup in gve_tx_clean_pending_packets for QPL
In DQ-QPL mode, gve_tx_clean_pending_packets() incorrectly uses the RDA
buffer cleanup path. It iterates num_bufs times and attempts to unmap
entries in the dma array.
This leads to two issues:
1. The dma array shares storage with tx_qpl_buf_ids (union).
Interpreting buffer IDs as DMA addresses results in attempting to
unmap incorrect memory locations.
2. num_bufs in QPL mode (counting 2K chunks) can significantly exceed
the size of the dma array, causing out-of-bounds access warnings
(trace below is how we noticed this issue).
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/drivers/net/ethernet/google/gve/gve_tx_dqo.c:178:5 index 18 is out of
range for type 'dma_addr_t[18]' (aka 'unsigned long long[18]')
Workqueue: gve gve_service_task [gve]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0xa0
__ubsan_handle_out_of_bounds+0xdc/0x110
gve_tx_stop_ring_dqo+0x182/0x200 [gve]
gve_close+0x1be/0x450 [gve]
gve_reset+0x99/0x120 [gve]
gve_service_task+0x61/0x100 [gve]
process_scheduled_works+0x1e9/0x380
Fix this by properly checking for QPL mode and delegating to
gve_free_tx_qpl_bufs() to reclaim the buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: cirrus: cs42l43: Fix double-put in cs42l43_pin_probe()
devm_add_action_or_reset() already invokes the action on failure,
so the explicit put causes a double-put. |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: check metadata block offset is within range
Syzkaller reports a "general protection fault in squashfs_copy_data"
This is ultimately caused by a corrupted index look-up table, which
produces a negative metadata block offset.
This is subsequently passed to squashfs_copy_data (via
squashfs_read_metadata) where the negative offset causes an out of bounds
access.
The fix is to check that the offset is within range in
squashfs_read_metadata. This will trap this and other cases. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: Fix memory leak in ice_set_ringparam()
In ice_set_ringparam, tx_rings and xdp_rings are allocated before
rx_rings. If the allocation of rx_rings fails, the code jumps to
the done label leaking both tx_rings and xdp_rings. Furthermore, if
the setup of an individual Rx ring fails during the loop, the code jumps
to the free_tx label which releases tx_rings but leaks xdp_rings.
Fix this by introducing a free_xdp label and updating the error paths to
ensure both xdp_rings and tx_rings are properly freed if rx_rings
allocation or setup fails.
Compile tested only. Issue found using a prototype static analysis tool
and code review. |
