| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx8m-blk-ctrl: fix out-of-range access of bc->domains
Fix out-of-range access of bc->domains in imx8m_blk_ctrl_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: Sanitize syscall table indexing under speculation
The syscall number is a user-controlled value used to index into the
syscall table. Use array_index_nospec() to clamp this value after the
bounds check to prevent speculative out-of-bounds access and subsequent
data leakage via cache side channels. |
| In the Linux kernel, the following vulnerability has been resolved:
mm, shmem: prevent infinite loop on truncate race
When truncating a large swap entry, shmem_free_swap() returns 0 when the
entry's index doesn't match the given index due to lookup alignment. The
failure fallback path checks if the entry crosses the end border and
aborts when it happens, so truncate won't erase an unexpected entry or
range. But one scenario was ignored.
When `index` points to the middle of a large swap entry, and the large
swap entry doesn't go across the end border, find_get_entries() will
return that large swap entry as the first item in the batch with
`indices[0]` equal to `index`. The entry's base index will be smaller
than `indices[0]`, so shmem_free_swap() will fail and return 0 due to the
"base < index" check. The code will then call shmem_confirm_swap(), get
the order, check if it crosses the END boundary (which it doesn't), and
retry with the same index.
The next iteration will find the same entry again at the same index with
same indices, leading to an infinite loop.
Fix this by retrying with a round-down index, and abort if the index is
smaller than the truncate range. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: Intel-thc-hid: Intel-thc: Add safety check for reading DMA buffer
Add DMA buffer readiness check before reading DMA buffer to avoid
unexpected NULL pointer accessing. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: tegra210-quad: Protect curr_xfer check in IRQ handler
Now that all other accesses to curr_xfer are done under the lock,
protect the curr_xfer NULL check in tegra_qspi_isr_thread() with the
spinlock. Without this protection, the following race can occur:
CPU0 (ISR thread) CPU1 (timeout path)
---------------- -------------------
if (!tqspi->curr_xfer)
// sees non-NULL
spin_lock()
tqspi->curr_xfer = NULL
spin_unlock()
handle_*_xfer()
spin_lock()
t = tqspi->curr_xfer // NULL!
... t->len ... // NULL dereference!
With this patch, all curr_xfer accesses are now properly synchronized.
Although all accesses to curr_xfer are done under the lock, in
tegra_qspi_isr_thread() it checks for NULL, releases the lock and
reacquires it later in handle_cpu_based_xfer()/handle_dma_based_xfer().
There is a potential for an update in between, which could cause a NULL
pointer dereference.
To handle this, add a NULL check inside the handlers after acquiring
the lock. This ensures that if the timeout path has already cleared
curr_xfer, the handler will safely return without dereferencing the
NULL pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix UAF in binder_netlink_report()
Oneway transactions sent to frozen targets via binder_proc_transaction()
return a BR_TRANSACTION_PENDING_FROZEN error but they are still treated
as successful since the target is expected to thaw at some point. It is
then not safe to access 't' after BR_TRANSACTION_PENDING_FROZEN errors
as the transaction could have been consumed by the now thawed target.
This is the case for binder_netlink_report() which derreferences 't'
after a pending frozen error, as pointed out by the following KASAN
report:
==================================================================
BUG: KASAN: slab-use-after-free in binder_netlink_report.isra.0+0x694/0x6c8
Read of size 8 at addr ffff00000f98ba38 by task binder-util/522
CPU: 4 UID: 0 PID: 522 Comm: binder-util Not tainted 6.19.0-rc6-00015-gc03e9c42ae8f #1 PREEMPT
Hardware name: linux,dummy-virt (DT)
Call trace:
binder_netlink_report.isra.0+0x694/0x6c8
binder_transaction+0x66e4/0x79b8
binder_thread_write+0xab4/0x4440
binder_ioctl+0x1fd4/0x2940
[...]
Allocated by task 522:
__kmalloc_cache_noprof+0x17c/0x50c
binder_transaction+0x584/0x79b8
binder_thread_write+0xab4/0x4440
binder_ioctl+0x1fd4/0x2940
[...]
Freed by task 488:
kfree+0x1d0/0x420
binder_free_transaction+0x150/0x234
binder_thread_read+0x2d08/0x3ce4
binder_ioctl+0x488/0x2940
[...]
==================================================================
Instead, make a transaction copy so the data can be safely accessed by
binder_netlink_report() after a pending frozen error. While here, add a
comment about not using t->buffer in binder_netlink_report(). |
| In the Linux kernel, the following vulnerability has been resolved:
smb/server: fix refcount leak in parse_durable_handle_context()
When the command is a replay operation and -ENOEXEC is returned,
the refcount of ksmbd_file must be released. |
| In the Linux kernel, the following vulnerability has been resolved:
linkwatch: use __dev_put() in callers to prevent UAF
After linkwatch_do_dev() calls __dev_put() to release the linkwatch
reference, the device refcount may drop to 1. At this point,
netdev_run_todo() can proceed (since linkwatch_sync_dev() sees an
empty list and returns without blocking), wait for the refcount to
become 1 via netdev_wait_allrefs_any(), and then free the device
via kobject_put().
This creates a use-after-free when __linkwatch_run_queue() tries to
call netdev_unlock_ops() on the already-freed device.
Note that adding netdev_lock_ops()/netdev_unlock_ops() pair in
netdev_run_todo() before kobject_put() would not work, because
netdev_lock_ops() is conditional - it only locks when
netdev_need_ops_lock() returns true. If the device doesn't require
ops_lock, linkwatch won't hold any lock, and netdev_run_todo()
acquiring the lock won't provide synchronization.
Fix this by moving __dev_put() from linkwatch_do_dev() to its
callers. The device reference logically pairs with de-listing the
device, so it's reasonable for the caller that did the de-listing
to release it. This allows placing __dev_put() after all device
accesses are complete, preventing UAF.
The bug can be reproduced by adding mdelay(2000) after
linkwatch_do_dev() in __linkwatch_run_queue(), then running:
ip tuntap add mode tun name tun_test
ip link set tun_test up
ip link set tun_test carrier off
ip link set tun_test carrier on
sleep 0.5
ip tuntap del mode tun name tun_test
KASAN report:
==================================================================
BUG: KASAN: use-after-free in netdev_need_ops_lock include/net/netdev_lock.h:33 [inline]
BUG: KASAN: use-after-free in netdev_unlock_ops include/net/netdev_lock.h:47 [inline]
BUG: KASAN: use-after-free in __linkwatch_run_queue+0x865/0x8a0 net/core/link_watch.c:245
Read of size 8 at addr ffff88804de5c008 by task kworker/u32:10/8123
CPU: 0 UID: 0 PID: 8123 Comm: kworker/u32:10 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: events_unbound linkwatch_event
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x100/0x190 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0x156/0x4c9 mm/kasan/report.c:482
kasan_report+0xdf/0x1a0 mm/kasan/report.c:595
netdev_need_ops_lock include/net/netdev_lock.h:33 [inline]
netdev_unlock_ops include/net/netdev_lock.h:47 [inline]
__linkwatch_run_queue+0x865/0x8a0 net/core/link_watch.c:245
linkwatch_event+0x8f/0xc0 net/core/link_watch.c:304
process_one_work+0x9c2/0x1840 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x5da/0xe40 kernel/workqueue.c:3421
kthread+0x3b3/0x730 kernel/kthread.c:463
ret_from_fork+0x754/0xaf0 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
</TASK>
================================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
spi: tegra210-quad: Protect curr_xfer in tegra_qspi_combined_seq_xfer
The curr_xfer field is read by the IRQ handler without holding the lock
to check if a transfer is in progress. When clearing curr_xfer in the
combined sequence transfer loop, protect it with the spinlock to prevent
a race with the interrupt handler.
Protect the curr_xfer clearing at the exit path of
tegra_qspi_combined_seq_xfer() with the spinlock to prevent a race
with the interrupt handler that reads this field.
Without this protection, the IRQ handler could read a partially updated
curr_xfer value, leading to NULL pointer dereference or use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_u32: use skb_header_pointer_careful()
skb_header_pointer() does not fully validate negative @offset values.
Use skb_header_pointer_careful() instead.
GangMin Kim provided a report and a repro fooling u32_classify():
BUG: KASAN: slab-out-of-bounds in u32_classify+0x1180/0x11b0
net/sched/cls_u32.c:221 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: sync read disk super and set block size
When the user performs a btrfs mount, the block device is not set
correctly. The user sets the block size of the block device to 0x4000
by executing the BLKBSZSET command.
Since the block size change also changes the mapping->flags value, this
further affects the result of the mapping_min_folio_order() calculation.
Let's analyze the following two scenarios:
Scenario 1: Without executing the BLKBSZSET command, the block size is
0x1000, and mapping_min_folio_order() returns 0;
Scenario 2: After executing the BLKBSZSET command, the block size is
0x4000, and mapping_min_folio_order() returns 2.
do_read_cache_folio() allocates a folio before the BLKBSZSET command
is executed. This results in the allocated folio having an order value
of 0. Later, after BLKBSZSET is executed, the block size increases to
0x4000, and the mapping_min_folio_order() calculation result becomes 2.
This leads to two undesirable consequences:
1. filemap_add_folio() triggers a VM_BUG_ON_FOLIO(folio_order(folio) <
mapping_min_folio_order(mapping)) assertion.
2. The syzbot report [1] shows a null pointer dereference in
create_empty_buffers() due to a buffer head allocation failure.
Synchronization should be established based on the inode between the
BLKBSZSET command and read cache page to prevent inconsistencies in
block size or mapping flags before and after folio allocation.
[1]
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:create_empty_buffers+0x4d/0x480 fs/buffer.c:1694
Call Trace:
folio_create_buffers+0x109/0x150 fs/buffer.c:1802
block_read_full_folio+0x14c/0x850 fs/buffer.c:2403
filemap_read_folio+0xc8/0x2a0 mm/filemap.c:2496
do_read_cache_folio+0x266/0x5c0 mm/filemap.c:4096
do_read_cache_page mm/filemap.c:4162 [inline]
read_cache_page_gfp+0x29/0x120 mm/filemap.c:4195
btrfs_read_disk_super+0x192/0x500 fs/btrfs/volumes.c:1367 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wlcore: ensure skb headroom before skb_push
This avoids occasional skb_under_panic Oops from wl1271_tx_work. In this case, headroom is
less than needed (typically 110 - 94 = 16 bytes). |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/dmem: fix NULL pointer dereference when setting max
An issue was triggered:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 15 UID: 0 PID: 658 Comm: bash Tainted: 6.19.0-rc6-next-2026012
Tainted: [O]=OOT_MODULE
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
RIP: 0010:strcmp+0x10/0x30
RSP: 0018:ffffc900017f7dc0 EFLAGS: 00000246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff888107cd4358
RDX: 0000000019f73907 RSI: ffffffff82cc381a RDI: 0000000000000000
RBP: ffff8881016bef0d R08: 000000006c0e7145 R09: 0000000056c0e714
R10: 0000000000000001 R11: ffff888107cd4358 R12: 0007ffffffffffff
R13: ffff888101399200 R14: ffff888100fcb360 R15: 0007ffffffffffff
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000105c79000 CR4: 00000000000006f0
Call Trace:
<TASK>
dmemcg_limit_write.constprop.0+0x16d/0x390
? __pfx_set_resource_max+0x10/0x10
kernfs_fop_write_iter+0x14e/0x200
vfs_write+0x367/0x510
ksys_write+0x66/0xe0
do_syscall_64+0x6b/0x390
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f42697e1887
It was trriggered setting max without limitation, the command is like:
"echo test/region0 > dmem.max". To fix this issue, add check whether
options is valid after parsing the region_name. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Prevent excessive number of frames
In this case, the user constructed the parameters with maxpacksize 40
for rate 22050 / pps 1000, and packsize[0] 22 packsize[1] 23. The buffer
size for each data URB is maxpacksize * packets, which in this example
is 40 * 6 = 240; When the user performs a write operation to send audio
data into the ALSA PCM playback stream, the calculated number of frames
is packsize[0] * packets = 264, which exceeds the allocated URB buffer
size, triggering the out-of-bounds (OOB) issue reported by syzbot [1].
Added a check for the number of single data URB frames when calculating
the number of frames to prevent [1].
[1]
BUG: KASAN: slab-out-of-bounds in copy_to_urb+0x261/0x460 sound/usb/pcm.c:1487
Write of size 264 at addr ffff88804337e800 by task syz.0.17/5506
Call Trace:
copy_to_urb+0x261/0x460 sound/usb/pcm.c:1487
prepare_playback_urb+0x953/0x13d0 sound/usb/pcm.c:1611
prepare_outbound_urb+0x377/0xc50 sound/usb/endpoint.c:333 |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: mmp_pdma: Fix race condition in mmp_pdma_residue()
Add proper locking in mmp_pdma_residue() to prevent use-after-free when
accessing descriptor list and descriptor contents.
The race occurs when multiple threads call tx_status() while the tasklet
on another CPU is freeing completed descriptors:
CPU 0 CPU 1
----- -----
mmp_pdma_tx_status()
mmp_pdma_residue()
-> NO LOCK held
list_for_each_entry(sw, ..)
DMA interrupt
dma_do_tasklet()
-> spin_lock(&desc_lock)
list_move(sw->node, ...)
spin_unlock(&desc_lock)
| dma_pool_free(sw) <- FREED!
-> access sw->desc <- UAF!
This issue can be reproduced when running dmatest on the same channel with
multiple threads (threads_per_chan > 1).
Fix by protecting the chain_running list iteration and descriptor access
with the chan->desc_lock spinlock. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Don't clobber irqfd routing type when deassigning irqfd
When deassigning a KVM_IRQFD, don't clobber the irqfd's copy of the IRQ's
routing entry as doing so breaks kvm_arch_irq_bypass_del_producer() on x86
and arm64, which explicitly look for KVM_IRQ_ROUTING_MSI. Instead, to
handle a concurrent routing update, verify that the irqfd is still active
before consuming the routing information. As evidenced by the x86 and
arm64 bugs, and another bug in kvm_arch_update_irqfd_routing() (see below),
clobbering the entry type without notifying arch code is surprising and
error prone.
As a bonus, checking that the irqfd is active provides a convenient
location for documenting _why_ KVM must not consume the routing entry for
an irqfd that is in the process of being deassigned: once the irqfd is
deleted from the list (which happens *before* the eventfd is detached), it
will no longer receive updates via kvm_irq_routing_update(), and so KVM
could deliver an event using stale routing information (relative to
KVM_SET_GSI_ROUTING returning to userspace).
As an even better bonus, explicitly checking for the irqfd being active
fixes a similar bug to the one the clobbering is trying to prevent: if an
irqfd is deactivated, and then its routing is changed,
kvm_irq_routing_update() won't invoke kvm_arch_update_irqfd_routing()
(because the irqfd isn't in the list). And so if the irqfd is in bypass
mode, IRQs will continue to be posted using the old routing information.
As for kvm_arch_irq_bypass_del_producer(), clobbering the routing type
results in KVM incorrectly keeping the IRQ in bypass mode, which is
especially problematic on AMD as KVM tracks IRQs that are being posted to
a vCPU in a list whose lifetime is tied to the irqfd.
Without the help of KASAN to detect use-after-free, the most common
sympton on AMD is a NULL pointer deref in amd_iommu_update_ga() due to
the memory for irqfd structure being re-allocated and zeroed, resulting
in irqfd->irq_bypass_data being NULL when read by
avic_update_iommu_vcpu_affinity():
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 40cf2b9067 P4D 40cf2b9067 PUD 408362a067 PMD 0
Oops: Oops: 0000 [#1] SMP
CPU: 6 UID: 0 PID: 40383 Comm: vfio_irq_test
Tainted: G U W O 6.19.0-smp--5dddc257e6b2-irqfd #31 NONE
Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025
RIP: 0010:amd_iommu_update_ga+0x19/0xe0
Call Trace:
<TASK>
avic_update_iommu_vcpu_affinity+0x3d/0x90 [kvm_amd]
__avic_vcpu_load+0xf4/0x130 [kvm_amd]
kvm_arch_vcpu_load+0x89/0x210 [kvm]
vcpu_load+0x30/0x40 [kvm]
kvm_arch_vcpu_ioctl_run+0x45/0x620 [kvm]
kvm_vcpu_ioctl+0x571/0x6a0 [kvm]
__se_sys_ioctl+0x6d/0xb0
do_syscall_64+0x6f/0x9d0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x46893b
</TASK>
---[ end trace 0000000000000000 ]---
If AVIC is inhibited when the irfd is deassigned, the bug will manifest as
list corruption, e.g. on the next irqfd assignment.
list_add corruption. next->prev should be prev (ffff8d474d5cd588),
but was 0000000000000000. (next=ffff8d8658f86530).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:31!
Oops: invalid opcode: 0000 [#1] SMP
CPU: 128 UID: 0 PID: 80818 Comm: vfio_irq_test
Tainted: G U W O 6.19.0-smp--f19dc4d680ba-irqfd #28 NONE
Tainted: [U]=USER, [W]=WARN, [O]=OOT_MODULE
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.78.2-0 09/05/2025
RIP: 0010:__list_add_valid_or_report+0x97/0xc0
Call Trace:
<TASK>
avic_pi_update_irte+0x28e/0x2b0 [kvm_amd]
kvm_pi_update_irte+0xbf/0x190 [kvm]
kvm_arch_irq_bypass_add_producer+0x72/0x90 [kvm]
irq_bypass_register_consumer+0xcd/0x170 [irqbypa
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: fixup hang in nvmet_tcp_listen_data_ready()
When the socket is closed while in TCP_LISTEN a callback is run to
flush all outstanding packets, which in turns calls
nvmet_tcp_listen_data_ready() with the sk_callback_lock held.
So we need to check if we are in TCP_LISTEN before attempting
to get the sk_callback_lock() to avoid a deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: ocb: skip rx_no_sta when interface is not joined
ieee80211_ocb_rx_no_sta() assumes a valid channel context, which is only
present after JOIN_OCB.
RX may run before JOIN_OCB is executed, in which case the OCB interface
is not operational. Skip RX peer handling when the interface is not
joined to avoid warnings in the RX path. |
| In the Linux kernel, the following vulnerability has been resolved:
macvlan: fix error recovery in macvlan_common_newlink()
valis provided a nice repro to crash the kernel:
ip link add p1 type veth peer p2
ip link set address 00:00:00:00:00:20 dev p1
ip link set up dev p1
ip link set up dev p2
ip link add mv0 link p2 type macvlan mode source
ip link add invalid% link p2 type macvlan mode source macaddr add 00:00:00:00:00:20
ping -c1 -I p1 1.2.3.4
He also gave a very detailed analysis:
<quote valis>
The issue is triggered when a new macvlan link is created with
MACVLAN_MODE_SOURCE mode and MACVLAN_MACADDR_ADD (or
MACVLAN_MACADDR_SET) parameter, lower device already has a macvlan
port and register_netdevice() called from macvlan_common_newlink()
fails (e.g. because of the invalid link name).
In this case macvlan_hash_add_source is called from
macvlan_change_sources() / macvlan_common_newlink():
This adds a reference to vlan to the port's vlan_source_hash using
macvlan_source_entry.
vlan is a pointer to the priv data of the link that is being created.
When register_netdevice() fails, the error is returned from
macvlan_newlink() to rtnl_newlink_create():
if (ops->newlink)
err = ops->newlink(dev, ¶ms, extack);
else
err = register_netdevice(dev);
if (err < 0) {
free_netdev(dev);
goto out;
}
and free_netdev() is called, causing a kvfree() on the struct
net_device that is still referenced in the source entry attached to
the lower device's macvlan port.
Now all packets sent on the macvlan port with a matching source mac
address will trigger a use-after-free in macvlan_forward_source().
</quote valis>
With all that, my fix is to make sure we call macvlan_flush_sources()
regardless of @create value whenever "goto destroy_macvlan_port;"
path is taken.
Many thanks to valis for following up on this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
net: cpsw: Execute ndo_set_rx_mode callback in a work queue
Commit 1767bb2d47b7 ("ipv6: mcast: Don't hold RTNL for
IPV6_ADD_MEMBERSHIP and MCAST_JOIN_GROUP.") removed the RTNL lock for
IPV6_ADD_MEMBERSHIP and MCAST_JOIN_GROUP operations. However, this
change triggered the following call trace on my BeagleBone Black board:
WARNING: net/8021q/vlan_core.c:236 at vlan_for_each+0x120/0x124, CPU#0: rpcbind/481
RTNL: assertion failed at net/8021q/vlan_core.c (236)
Modules linked in:
CPU: 0 UID: 997 PID: 481 Comm: rpcbind Not tainted 6.19.0-rc7-next-20260130-yocto-standard+ #35 PREEMPT
Hardware name: Generic AM33XX (Flattened Device Tree)
Call trace:
unwind_backtrace from show_stack+0x28/0x2c
show_stack from dump_stack_lvl+0x30/0x38
dump_stack_lvl from __warn+0xb8/0x11c
__warn from warn_slowpath_fmt+0x130/0x194
warn_slowpath_fmt from vlan_for_each+0x120/0x124
vlan_for_each from cpsw_add_mc_addr+0x54/0x98
cpsw_add_mc_addr from __hw_addr_ref_sync_dev+0xc4/0xec
__hw_addr_ref_sync_dev from __dev_mc_add+0x78/0x88
__dev_mc_add from igmp6_group_added+0x84/0xec
igmp6_group_added from __ipv6_dev_mc_inc+0x1fc/0x2f0
__ipv6_dev_mc_inc from __ipv6_sock_mc_join+0x124/0x1b4
__ipv6_sock_mc_join from do_ipv6_setsockopt+0x84c/0x1168
do_ipv6_setsockopt from ipv6_setsockopt+0x88/0xc8
ipv6_setsockopt from do_sock_setsockopt+0xe8/0x19c
do_sock_setsockopt from __sys_setsockopt+0x84/0xac
__sys_setsockopt from ret_fast_syscall+0x0/0x54
This trace occurs because vlan_for_each() is called within
cpsw_ndo_set_rx_mode(), which expects the RTNL lock to be held.
Since modifying vlan_for_each() to operate without the RTNL lock is not
straightforward, and because ndo_set_rx_mode() is invoked both with and
without the RTNL lock across different code paths, simply adding
rtnl_lock() in cpsw_ndo_set_rx_mode() is not a viable solution.
To resolve this issue, we opt to execute the actual processing within
a work queue, following the approach used by the icssg-prueth driver.
Please note: To reproduce this issue, I manually reverted the changes to
am335x-bone-common.dtsi from commit c477358e66a3 ("ARM: dts: am335x-bone:
switch to new cpsw switch drv") in order to revert to the legacy cpsw
driver. |
